Introduction: What the Hikvision DS-K1108ADK Offers
The Hikvision DS-K1108ADK is a Pro‑Series wall‑mount access control reader that combines DESFire card support with an integrated 12‑button numeric keypad and rugged outdoor protection. Designed for controller‑based systems such as Hikvision's DS‑K2600T / DS‑K2800 series, the DS‑K1108ADK supports 13.56 MHz card technologies (MIFARE, DESFire and where applicable FeliCa) and flexible communications including RS‑485, Wiegand and OSDP. With IP65 ingress protection, tamper detection, status LEDs and a built‑in buzzer, it is aimed at installers and integrators who need a compact, secure reader for both indoor and outdoor door entry points.
Key Features at a Glance
- Card technologies:ISO 14443‑A (13.56 MHz) support for MIFARE, DESFire and FeliCa variants.
- PIN support:Integrated 12‑button numeric keypad enables PIN and card+PIN multi‑factor authentication.
- Flexible communications:Selectable RS‑485, Wiegand (26/34) and OSDP via DIP switches for compatibility with a wide range of controllers.
- Rugged design:IP65 rating for outdoor mounting and an operating range of −20 °C to +65 °C.
- Security & usability:Tamper detection, audible buzzer, status LEDs and support for online firmware upgrades.
- Low power:12 V DC supply and typical power consumption ≤ 2 W; typical read distance ≈ 50 mm.
Detailed Specifications and Benefits
Below is a breakdown of the DS‑K1108ADK's technical specifications and the practical benefits they bring to installations.
- Model & series:DS‑K1108ADK, Pro‑Series DS‑K1108A family. Compact wall‑mount form factor (123 × 88 × 21 mm) and light weight (~0.14 kg net) make it easy to place at standard door mounting heights.
- Mounting:Surface wall mount for quick installation on standard backboxes or flat wall surfaces.
- Card standard:ISO 14443‑A (13.56 MHz), covering MIFARE Classic/MIFARE DESFire and FeliCa variants. Supporting DESFire is important for higher‑security credential deployments and compatibility with modern credential provisioning workflows.
- Authentication modes:Card-only, PIN-only (via keypad) or Card + PIN for two‑factor authentication. Card+PIN is ideal where you need to raise the security bar without provisioning additional hardware.
- Protocols:RS‑485, Wiegand 26/34 and OSDP are selectable with DIP switches. This gives integrators maximum flexibility: use Wiegand for legacy controllers, RS‑485 for longer runs and OSDP for encrypted, bi‑directional communication with modern controllers.
- Firmware:Supports online firmware upgrades so devices in the field can receive updates without full replacement—useful for security patches or new features.
- Power:12 V DC supply; typical consumption ≤ 2 W. Low power draw keeps wiring and power budgeting simple for most access control panels.
- Read distance:Typical ≈ 50 mm—suitable for hands‑free presenting of credentials at door height while avoiding accidental reads from farther away.
- Ingress & temperature:IP65 rated and operational between −20 °C and +65 °C, making the reader suitable for outdoor entrances, sheltered gateways and industrial sites where weather resistance is required.
- Security features:Tamper detection input, status LEDs and buzzer support immediate local alarm and operator feedback during tamper or forced entry conditions.
Use Cases: Where the DS-K1108ADK Excels
- Commercial office entries:Provides easy integration with controller-based solutions, enabling card + PIN workflows for areas that require elevated authentication (server rooms, HR areas, executive suites).
- Residential and multi‑tenant buildings:Weatherproofing and small footprint make it a good fit for apartment block entry systems where residents use DESFire or MIFARE credentials plus optional PINs.
- Industrial or outdoor sites:IP65 protection and wide operating temperature range allow mounting at gatehouses, loading bays or manufacturing plant doors exposed to elements.
- Retrofit and phased upgrades:Selectable Wiegand/RS‑485/OSDP support helps integrators upgrade legacy systems in stages—use existing panels with Wiegand now, migrate to OSDP with newer controllers later.
- High‑security areas:Card+PIN mode adds an additional authentication factor without requiring biometrics; useful where higher assurance is needed but biometric hardware is undesirable.
Comparisons with Similar Products
The DS‑K1108ADK sits in a crowded market of 13.56 MHz readers. Here are a few practical comparisons to help position it against alternatives.
- Hikvision ecosystem benefits:Native compatibility with Hikvision access controllers and management software often simplifies commissioning, telemetry and firmware workflows compared with generic readers that may require protocol translation.
- Third‑party readers (HID, Suprema, etc.):Some competitors offer broader credential ecosystems (e.g., HID iCLASS, multi‑frequency support, stronger PKI credential management) or additional form factors. If you need enterprise credential lifecycle management or multi‑technology readers (125 kHz + 13.56 MHz + BLE), some competitors may be preferable.
- Integrated keypad advantage:Readers with built‑in numeric pads, like the DS‑K1108ADK, enable PIN and card+PIN flows without additional hardware. This reduces installation complexity on doors requiring two‑factor authentication.
- No keypad models:Cheaper keypad‑less readers are suitable where card-only access is acceptable but don’t provide the extra security layer for sensitive zones.
- Selectable interface:The DS‑K1108ADK’s DIP‑selectable RS‑485, Wiegand and OSDP is a practical middle ground—some lower‑cost readers only offer Wiegand; higher‑end readers may default to OSDP and offer advanced encryption. The DS‑K1108ADK makes it easier to support mixed or transitional infrastructures.
Customer Feedback & Installer Notes
There are no verified customer testimonials supplied with this product listing. Based on common installer feedback for similar Hikvision Pro‑Series readers, typical strengths and areas to watch include:
- Strengths commonly reported:Reliable card reads, solid weatherproofing, compact size for tidy installations, and the convenience of integrated keypad and protocol selection.
- Common considerations:Ensure controller firmware compatibility—particularly when using OSDP or DESFire features—and verify credential types and sector/applications to match existing card inventories. Some integrators note that where enterprise credential management (PKI issuance, mobile credential provisioning) is required, specialist readers or additional middleware may be needed.
Compliance, Installation Tips & Pricing Notes
- Compliance & markings:Check the supplied unit and documentation for CE/UKCA and any local compliance markings required by your region.
- Installation basics:Observe standard low‑voltage installation practice: isolate power before wiring, follow Hikvision controller wiring diagrams for tamper and alarm inputs, and test all reader modes (card, PIN, card+PIN) during commissioning.
- Pricing:You provided a cost price of 74.94 and a suggested minimal RRP of 89.21 which reflects an approximate 16% margin. Please confirm the currency for these amounts (e.g., GBP, EUR, USD) and whether you want prices shown inclusive or exclusive of VAT so final RRPs and tiered pricing (conservative / market / premium) can be produced and compared with reseller listings.
Conclusion: Why Choose the DS-K1108ADK?
The Hikvision DS‑K1108ADK is a balanced, installer‑friendly access control reader that pairs DESFire card support with an integrated keypad and rugged outdoor credentials. It is particularly well suited to controller‑based installations where flexibility matters: installers can select between Wiegand for legacy systems, RS‑485 for long runs or OSDP for secure, encrypted communications. The addition of PIN and card+PIN modes without additional hardware keeps costs and complexity down while improving security for sensitive doors.
For projects that require a compact, weatherproof reader that integrates seamlessly into Hikvision controller ecosystems, and where card+PIN authentication is desirable, the DS‑K1108ADK represents a practical, cost‑effective choice. If you need help with pricing (currency/VAT), deployment scenarios or comparisons against a specific competitor model, tell me the currency and whether prices should include VAT and I will produce tailored RRPs and a comparative price table.
