Veracity OUTREACH Max PoE Extender, 10/100 Ethernet, PoE Pass‑Through VOR‑ORM

Introduction: Meet the Veracity OUTREACH Max PoE Extender

The Veracity OUTREACH Max (VOR‑ORM) is a compact, PoE‑powered Ethernet repeater designed to break the 100‑metre Ethernet limitation for IP cameras, wireless access points and other PoE devices. Marketed as a simple, installer‑friendly device, the OUTREACH Max transparently forwards Power over Ethernet (including IEEE 802.3af, 802.3at and 802.3bt/custom 4‑pair types) while restoring the Ethernet link every 100 metres so devices can be placed up to 200 metres from the switch without a local power outlet. With plug‑and‑play operation, low power draw and a small footprint, it targets CCTV installers, system integrators and site upgrade projects where extending PoE reliably is essential.

• Extend up to 200 m per segment— doubles the conventional 100 m Ethernet reach for 10/100 devices.
• Transparent PoE pass‑through— supports IEEE 802.3af/at and 802.3bt/custom 4‑pair forwarding, with datasheet examples showing up to ~90 W in some configurations.
• Plug‑and‑play— two auto‑configuring RJ45 ports with auto MDI/MDI‑X; no manual configuration required.
• Small and install‑friendly— integrated mounting holes and a lightweight design make it easy to fit inside enclosures or on surfaces.
• Low power draw— consumes approximately 1.3 W, powered entirely from the PoE feed.

For many CCTV and wireless deployments, the inability to reach devices beyond 100 metres without local power is a frequent installation pain point. The OUTREACH Max addresses that by restoring the Ethernet signal and forwarding PoE at the 100‑metre mark, enabling longer runs without adding mains power or complex infrastructure changes. Its support for 4‑pair PoE (802.3bt / custom 4‑pair) makes it suitable where higher power delivery is required for modern cameras or heaters.

• Model:VOR‑ORM (OUTREACH Max)
• Product type:Ethernet & PoE extender
• Power consumption:≈1.3 W (drawn via PoE) — minimal impact on available power for the downstream device.
• PoE compatibility:IEEE 802.3af / 802.3at / 802.3bt (custom 4‑pair, always‑on 48V compatible) — broad compatibility with modern PoE sources.
• Maximum forwarded PoE:Up to 90 W (application dependent; see datasheet) — supports higher‑power devices when correctly configured and cabled.
• Ethernet interface:Two auto‑configuring 10/100Base‑T RJ45 ports (auto MDI/MDI‑X) — simple cabling and immediate operation.
• Data rate:100 Mbps per segment (10/100) — full 100 Mbps bandwidth is maintained over each 100 m segment.
• Indicators:Power and Link/Activity per port — quick visual diagnostics.
• Dimensions & weight:105 × 40 × 22 mm; ≈45 g — compact for discreet mounting.
• Mounting:Two 7 mm diameter holes; centres 89 mm — fits common mounting patterns and enclosures.
• Operating environment:−10 °C to 50 °C; up to 85% non‑condensing humidity.
• Compliance:CE, FCC, UKCA, UL, RoHS.
• Power source:Powered by PoE — no local power required.

Benefits linked to these specifications include quick installation (no configuration), predictable power budgeting (consult the datasheet for chained configurations), and compatibility with a wide range of PoE switches and midspans. The low device draw preserves more of the source’s available power for the end device; this is especially important when using multiple chained units or feeding high‑power cameras.

The OUTREACH Max is essentially an inline repeater: it receives a 10/100Base‑T signal and PoE from a switch or injector, restores the Ethernet link at the unit and forwards both data and power to the downstream device. By placing one OUTREACH Max at the 100‑metre point, you can extend a run to approximately 200 metres for a 10/100 device without local mains power. Multiple units may be daisy‑chained to go farther, but delivered power will decrease depending on the source, number of extenders and cable quality.

• Cable recommendation:Use quality cable (Cat6 recommended for longer runs or higher power) to reduce voltage drop and preserve power delivery.
• Power planning:Always consult the Veracity datasheet/installation guide to calculate delivered power for chained units and to match your PoE source capacity.
• Mounting:The compact dimensions and mounting holes mean the device can be fixed inside junction boxes or on flat surfaces — useful for outdoor enclosures or indoor ceiling voids.

The OUTREACH Max fits a variety of real‑world deployment scenarios where extending PoE is needed but installing local mains power is impractical or costly:

• Perimeter and parking lot surveillance:Remote cameras mounted on poles or structures often sit beyond 100 metres from the nearest switch. The OUTREACH Max eliminates the need for local power or fiber transceivers.
• Large warehouses and factories:Wireless access points or cameras in long aisles can be powered and connected without additional electrical work.
• Retrofit projects:In heritage buildings or leased spaces where running new mains circuits isn’t feasible, this extender lets you add modern IP devices while preserving building fabric.
• Events and temporary installations:For film sets, outdoor events or temporary CCTV coverage, installers can run longer Ethernet runs without setting up temporary power distribution.
• Multi‑camera installations:When multiple cameras require higher power (e.g., heaters, wipers, PTZs), the OUTREACH Max’s 4‑pair forwarding capability helps deliver the needed power, subject to upstream capacity and cabling.

When assessing the OUTREACH Max against alternative approaches, consider the following points:

• Passive PoE extenders vs OUTREACH Max:Some low‑cost passive extenders lack standards compliance and robust forwarding of 4‑pair PoE. The OUTREACH Max supports IEEE standards and custom 4‑pair forwarding for higher power devices.
• Gigabit extenders and media converters:If you need Gigabit speeds, fiber media converters or specialized gigabit PoE extenders are required — OUTREACH Max is designed for 10/100 deployments and maintains 100 Mbps per segment.
• PoE injectors and midspans:Injectors provide power but don’t extend the 100 m Ethernet limit. OUTREACH Max complements injectors by extending both data and power.
• Other branded PoE repeaters:Competing repeaters may offer similar functionality, but the OUTREACH Max’s combination of 4‑pair compatibility, low power draw, compact size and compliance credentials is a strong package for many installers. Always compare delivered PoE figures for chained runs and confirm compatibility with your camera/WAP power requirements.

In short, choose OUTREACH Max when you need reliable 100 Mbps connectivity and transparent PoE forwarding over extended copper distances; consider fiber or gigabit‑capable solutions when your bandwidth or distance requirements exceed what a 10/100 repeater can offer.

Official, named testimonials are not provided here, but aggregated feedback from integrators and installers familiar with Veracity OUTREACH devices commonly highlights these practical points:

• Ease of installation:Plug‑and‑play setup and auto‑configuring ports make deployments fast and predictable.
• Reliability:The compact unit performs reliably in standard environmental ranges and fits neatly into existing junction boxes or enclosures.
• Power handling:Installers appreciate the 4‑pair forwarding capability for powering modern high‑draw cameras, though they stress the importance of checking the datasheet for chained configurations.
• Value:The suggested retail price (USD 179.99) positions the OUTREACH Max as a specialized but cost‑effective tool for extending PoE without major infrastructure changes.
• Common caveats:Users remind prospective buyers to plan cable type (Cat6 recommended), verify upstream power capacity and remember that the device supports 10/100 speeds only — not Gigabit.

The Veracity OUTREACH Max (VOR‑ORM) offers a practical, standards‑based solution for extending PoE and 10/100 Ethernet beyond the typical 100‑metre limit. Its transparent PoE pass‑through (including 4‑pair 802.3bt/custom support), low power draw and plug‑and‑play design make it particularly appealing to CCTV installers, system integrators and anyone needing to place cameras or WAPs where mains power is unavailable. While it isn’t a gigabit solution and delivered power can vary with chained units and cable quality, its compact form factor, compliance credentials and straightforward installation workflow deliver real site‑level benefits.

For projects that require extended runs of 10/100 devices and dependable PoE forwarding, the OUTREACH Max represents a sensible balance of performance, simplicity and value. For detailed power‑budget calculations, chaining tables and configuration scenarios, consult the Veracity datasheet and installation guide to confirm that the OUTREACH Max will meet your specific device and site requirements.